Bend Cost Schedule
Bend, OR · Deschutes, Crook & Jefferson Counties Price Schedule
How much does submersible well pump and pressure tank repair cost in Bend, OR? In Deschutes, Crook & Jefferson Counties, initial scopes start at $185 to $575, standard residential work averages $950 to $2,150, and major multi-stage projects run $2,450 to $5,600. Every matched specialist confirms a written price before work begins.
On-Site Megohm Diagnostic & Pressure Switch / Control Box
WP-01
Isolating surface electrical faults vs. down-hole motor failure; includes pressure switch or Franklin control box swap.
$185 to $495
Typical Bend Range
Pre-Charged Diaphragm Pressure Tank & Brass Tee Package
WP-02
Commercial-grade Well-X-Trol or Flexcon bladder tank, brass tank tee, relief valve, gauge, and drain cock.
$950 to $1,850
Typical Bend Range
Constant-Pressure VFD Controller Replacement (SubDrive / Pentek)
WP-03
Swapping lightning-damaged or faulted variable-frequency drive and pressure transducer sensor.
$1,350 to $2,450
Typical Bend Range
Submersible Well Pump & Motor Replacement (150 to 600+ ft)
WP-04
Full hoist-truck pull, new stainless pump end and motor, check valves, torque arrestor, and chlorination.
$2,450 to $5,600
Typical Bend Range
What Moves a Quote Up or Down
- •Static water level and pump setting depth on your Oregon Water Resources Department (OWRD) well log (e.g., 120 ft in La Pine vs. 520 ft in Tumalo or Powell Butte)
- •Motor horsepower and voltage required to lift water from that depth (0.75 HP to 1.5 HP standard vs. 2 HP to 5 HP deep high-head)
- •Drop-pipe material inside the casing (flexible poly pipe vs. threaded 21-foot Schedule 80 PVC or rigid galvanized steel requiring a heavy hoist boom)
- •Overhead hoist truck clearance above the wellhead (open driveway access vs. wellhead enclosed inside a roofed pumphouse shed)
Pricing & Dispatch Questions
Common questions about Bend estimates, scheduling, and scope options.
Is Bend Well Pump Repair the contractor that pulls the pump?
No. Bend Well Pump Repair is an independent local referral and dispatch service. When you submit a request, we route your details to one vetted well pump specialist serving Bend and Central Oregon who contacts you directly.
How do I know if my submersible pump is bad or if it is just an electrical part in the pumphouse?
You cannot tell without an ohmmeter and megohmmeter test at the control box. Roughly 40% to 50% of sudden no-water calls in Deschutes County turn out to be a burned pressure switch ($185 to $325), a failed start capacitor in the Franklin control box ($250 to $495), or a faulted VFD controller, none of which require pulling the pump from the well.
Why does well pump replacement cost more in Bend and Tumalo than in La Pine?
Depth and horsepower. La Pine wells tap a shallow alluvial aquifer typically 40 to 140 feet deep using a 0.5 or 0.75 HP pump. Wells in Bend, Tumalo, Alfalfa, and Redmond are drilled 300 to 650+ feet into fractured basalt and require a heavy boom hoist truck, 1.5 to 3+ HP motors, and heavy-wall drop pipe.
What if I do not know how deep my well is?
Every registered well in Deschutes, Crook, and Jefferson Counties has a public drilling report on file with the Oregon Water Resources Department (OWRD). Give your property street address or tax lot when the specialist calls, and they can look up your casing depth, static water level, and original GPM yield in 60 seconds.
Do you route emergency out-of-water requests in Redmond, Sisters, Tumalo, La Pine, and Prineville?
Yes. We route no-water and low-pressure requests across Bend, Tumalo, Alfalfa, Redmond, Terrebonne, Sisters, Sunriver, La Pine, Powell Butte, and Prineville.